Thứ Bảy, 19 tháng 8, 2023

Cutting Tool Fundamentals: Chip Formation, Chip Load and Milling tools

YCK2020 You can find this article again with keywords: Chip Formation, Chip Load, Climb vs. Conventional Milling, Cutting Tool Fundamentals, Rotation Direction

In machining, the combination of Cutting Speed, Feed, Tool and Workpiece affects the Machining quality of the part.

Rotation Direction

All tools (except left-handed taps) rotate clockwise (M3) when viewed from the machine spindle looking down at the part.


Cutting Tool Fundamentals: Chip Formation, Chip Load and Milling tools

Chip Formation

Cutting tools remove metal by shearing action as illustrated in Figure 3.11 below. As the tool advances into the material it causes a small amount of the material to shear away, forming a chip.


Cutting Tool Fundamentals: Chip Formation, Chip Load and Milling tools

Chip Load


The thickness of material sheared away by each cutting tooth is called the feed per tooth, or chip load. As the chip is ejected from the work area it carries with it some of the heat generated by the shearing process.


Cutting Tool Fundamentals: Chip Formation, Chip Load and Milling tools

A methodology for calculating cutting speeds and feeds is presented later in this chapter. One of the best ways to validate cutting speeds and feeds is to observe the chips created by the machining process. Chips should be curled and may change color due to heating.


After gaining some experience machinists are able to adjust cutting speeds and feeds based in part on the size, shape, and color of chips and on the sound produced by the cutting process.

Climb vs. Conventional Milling


Milling tools can advance through the material so that the cutting flutes engage the material at maximum thickness and then decreases to zero. This is called Climb Milling.


Cutting in the opposite direction causes the tool to scoop up the material, starting at zero thickness and increasing to maximum. This is called Conventional Milling.


Conventional milling is used often on manual machines because backlash in the machine lead screws causes the tool to lurch when climb cutting. This is not a problem on CNC machines because they use ball screws.


Conventional milling causes the tool to rub against the cutting surface, work hardening the material, generating heat, and increasing tool wear. Raking chips across the finished surface also produces a poorer surface finish.


Unless specifically recommended by the tool manufacturer for the material being milled, always use climb milling on a CNC. Climb milling produces far less cutting pressure and heat, leaves a better surface finish, and results in longer tool life..


Cutting Tool Fundamentals: Chip Formation, Chip Load and Milling tools

The above factors will be adjusted reasonably to complete the CNC precision machining process.


Figure 3.13: Climb vs. Conventional Milling



Hopefully, the article Cutting Tool Fundamentals - YCK2020 Blog will help you better understand Cutting Tool Fundamentals. If you have any discussion with us, please comment in the comment section at the end of the article. Good luck! 

 


Bạn có trao đổi gì về nội dung này không? Hãy để lại Comment trong phần Nhận xét cuối bài đăng nhé. Bài viết này thuộc chủ đề công bố trên Blog Yêu Cơ Khí #YCK2020 - Kênh chia sẻ kiến thức về Công nghệ Chế tạo máy.
Bạn muốn tìm kiếm gì không?

Không có nhận xét nào:

Đăng nhận xét

Nội dung bài viết này có hữu ích với bạn không? #YCK2020 - Dự án Hỗ trợ Cộng đồng Cơ khí Trẻ

Top All

Nguồn video của Blog Yêu Cơ khí YCK2020

Về chúng tôi

Về chúng tôi
Blog Yêu Cơ khí